Replace bulb fender lamp Hudson eight 1934???

JACK356

Hello

WHAT METHOD replace bulb fender lamp  left Hudson EIGHT 1934  Thank you.

JACK356

CURRENT IN THE VEINS 66 YEARS AFTER

JACK356

1 YEAR AGO

Rocket

Very easy put a blanket in front of the light in case you drop the lens now take your thumb and push the lens straight in towards the back of the light this is to make sure the lens is lose all away around the light body it dose not have to go in to far you just want to make sure it is lose now you just push the lens straight back while also pushing the lens up toward the inside the light body at this time the botton of the lens should be sticking out lightly pull on the botton of the lens pulling it out and downward the lens should be out know so change the bulb and replace the lens in reverse order I hope this helps.

Old Fogey UK

Jack,
I will send you a private email, attaching the lens manufacturers instructions for installing and removing lenses.
Regards,
David.

JACK356

Thank you. In the meantime I was able to unmount myself. Good block. Rare and fragile glass ;Bulb Mazda

For reassembly;j waits for your mail

JACK356

Replace bulbe interior???

54coupe

There is a snap ring at the outside edge of the glass.

JACK356

Thanks for the confirmation.I had noticed;but apparently well-gripped ring   

Rocket

I see that you have a felt type washer can you tell me were it goes I do not have any in mine I put my set together with parts I collected over time I also did not know there was a rubber pad on the bottom thanks Tom.

JACK356

felt between the reflector and ice.Original 1934 

Rocket

do you mean between the reflector and the lens and could you tell me the size of the felt I will have to buy some and make my own thanks Tom.

Rocket

JACK356 could you please post the measurements of the felt washer I have to make some for my lights thanks Tom.

JACK356

I'm looking at this. I'm working this weekend

JACK356

Thickness    3MM   FELT

Rocket

Thank you so much one other thing that I need is to know witch way the cup washer on the bottom of the base goes on I know it goes under the fender I need know witch way it is faceing when you put the nut on could you please post a picture of your base with the washer and nut on it so I put mine on the car the right way thanks Tom.

JACK356

Ok  tomorrow

Rocket

Thank you very much for every thing you are doing for me Tom.

JACK356

Original 1934

Rocket

Once again thank you can you tell me is your gasket made out of rubber that is the last part I will have to find somewere to complete my lights Tom.

JACK356

Incredible origin    

Old Fogey UK

Rocket said:

Once again thank you can you tell me is your gasket made out of rubber that is the last part I will have to find somewere to complete my lights Tom.

You can always cut your own gaskets, Tom.
 I have used old rubber inner tube to make all sorts of gaskets for my 1934.

Old Fogey UK

I used inner tube for exterior door handle mounting gaskets and for tail light mounting gaskets, as well as other places.
You just need good scissors and steady hands !

JACK356

Épaisseur 3MM FEUTRE  OK    

 chambre à air      

JACK356

Replacement.FASTER AND EASIER;

unseating the two screws from the support underneath.MOUNT THE JOINT pushing the reflector.Put the ice down.Push.and put it up. 3 min.

Jon B

Jack:

Rubber mounting pads are available for 1934 at Wildrick's, for $32 apiece. 

https://lh3.googleusercontent.com/pKIqVCyiheQsulgjxwCdrwFylDaBP9cGb43z-VrBvxqUPQThZMDT0Ni_dFLiWHFzeqEWilYL0ytXyahDBH1pB5o5Nw597eGxO32IItHKrLx9LHoQwIG-=w1280

Here is the webpage: https://www.wrphet.com/hudson-mounting-pads

Rocket

Jon B thank you so much for the information I called them and he is going to fix me up with them they were the last thing I needed to complete my lights.

Old Fogey UK

Jon B said:

Jack:

Rubber mounting pads are available for 1934 at Wildrick's, for $32 apiece. 

https://lh3.googleusercontent.com/pKIqVCyiheQsulgjxwCdrwFylDaBP9cGb43z-VrBvxqUPQThZMDT0Ni_dFLiWHFzeqEWilYL0ytXyahDBH1pB5o5Nw597eGxO32IItHKrLx9LHoQwIG-=w1280

Here is the webpage: https://www.wrphet.com/hudson-mounting-pads

Or use my inner tube method, Jon, and get them for nothing ! 

JACK356

Jon B said:

Jack:

Rubber mounting pads are available for 1934 at Wildrick's, for $32 apiece. 

https://lh3.googleusercontent.com/pKIqVCyiheQsulgjxwCdrwFylDaBP9cGb43z-VrBvxqUPQThZMDT0Ni_dFLiWHFzeqEWilYL0ytXyahDBH1pB5o5Nw597eGxO32IItHKrLx9LHoQwIG-=w1280

Here is the webpage: https://www.wrphet.com/hudson-mounting-pads


the joints are like new

Tapez votre commentaire

JACK356

Have you;references the hudson 1934 rear bulbs;left with the plate and right. Thank you

Rocket

Jack356 could you tell me were the wire from your fender light goes after you mount the light  is in attached to the fender somewere or dose it just go through inner fender panel and tie into the wireing somewere I am adding these lights to my car so I do not know were the wire goes thanks.